INSTALLATION INSTRUCTIONSAND USER GUIDEVENMAR MODELS BROAN MODELSEVO5 700 HRV HEPAEVO5 500 HRVHRV 7.1 HEPAHRV 5.1* These products earned the ENERGY ST
3.6 INSTALLING INSULATED FLEXIBLE DUCTS3.6.1 CONNECTION TO TANDEM TRANSITION10Make sure the vapor barrier on the insulated ducts does not tear during
11 3.6 INSTALLING INSULATED FLEXIBLE DUCTS (CONT’D)Use the following procedure for connecting the insulated flexible ducts to the unit ports (exhaust
12 3.7 INSTALLING DUAL EXTERIOR HOOD (CONT’D)3.7.3 CONNECTING TANDEM TRANSITION TO DUAL EXTERIOR HOODVD0084EXHAUST AIR TO OUTSIDE DUCT ON TOP Using a
13 3.8 CONNECTING THE DRAINCut two sections of plastic tubing, approximately 12” long, and connect each one to both inner drain fittings located under
4. CONTROLS (CONT’D) Detach the faceplate from the mounting plate by pulling the bottom part. If necessary, bore the mounting holes and insert anch
4. CONTROLS (CONT’D) 4.3 MAIN WALL CONTROL INSTALLATION (CONT’D) 4.4 WALL CONTROL(S) CONNECTION TO THE UNITSplice back the end of the cable to acces
4. CONTROLS (CONT’D) 4.5 MAIN WALL CONTROL DESCRIPTION16The included wall control is 40405 (intented for EVO5 500 HRV and EVO5 700 HRV HEPA Venmar uni
174. CONTROLS (CONT’D) 4.6 MAIN WALL CONTROL USE (CONT’D)4.6.1 OPERATION MODES (CONT’D)ECO MODEThe ventilation unit exchanges air intermittently on a
4. CONTROLS (CONT’D)18 4.6 MAIN WALL CONTROL USE (CONT’D)4.6.3 CHANGING RECIRCULATION TO OFF FOR AUTO AND ECO MODESNOTE: Prior to perform this settin
4. CONTROLS (CONT’D) 4.6 MAIN WALL CONTROL USE (CONT’D)4.6.6 HOW TO CHANGE MINIMUM AND MAXIMUM AIR EXCHANGE TEMPERATURE LIMITS FOR ECO AND AUTO MODES
First, we want to congratulate you on your purchase of this excellent unit which will allow you and your family to enjoy clean and healthy air through
205. MAINTENANCERisk of electric shock. Before performing any maintenance, always turn off and disconnect the unit from its power source. WARNING!Ref
215. MAINTENANCE (CONT’D) 5.2 REGULAR MAINTENANCEPerform this maintenance on the unit every time the wrench icon appears on wall control screen.VD0005
Reinstall the heat recovery core with its filters. For EVO5 700 HRV HEPA and HRV 7.1 HEPA units only: The heat recovery core must be reinstalled B
237. T ROUBLESHOOTINGIf the unit does not work properly, reset the unit by unplugging it for one minute and then replug it. If it is still not workin
WARRANTY - WHOLE-HOUSE AIR EXCHANGERThe manufacturer warrants to the original consumer purchaser of its products, that such products will be free from
TABLE OF CONTENTS31. T YPICAL INSTALLATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41. TYPICAL INSTALLATIONSUse the following illustrations as guidelines to help you decide on how the unit will be installed.All the units should be hu
52. DIMENSIONS 2.1 EVO5 700 HRV HEPA AND HRV 7.1 HEPA UNITS37 7/8”11¼”17 7/16”39 /8”12½”VK0082A 2.3 JOIST OPENING REQUIRED FOR TANDEM® TRANSITIONVD
63. INSTALLATION 3.1 INSPECT THE CONTENT OF THE BOX• Inspect the exterior of the unit for shipping damage. Ensure that there is no damage to the door
73. INSTALLATION 3.2 INSTALLATION KITS, TOOLS AND MATERIALThe installation kit needed to perform most installations is IKSV1000 for Venmar units and I
8 3.5 INSTALLING NON-INSULATED DUCTS AND DIFFUSERSStale air exhaust ductwork• Install the stale air exhaust diffuser in the main area where the conta
9 3.5 INSTALLING NON-INSULATED DUCTS AND DIFFUSERS (CONT’D)Stale air exhaust ductworkSame as for Fully Ducted System, described in step 3.5.1.3.5.2 CE
Commentaires sur ces manuels